WinFuture-Forum.de: Bluescreen Vor Der Installation (win 7, 64bit) - WinFuture-Forum.de

Zum Inhalt wechseln

Alle Informationen zum Thema Windows 7 in unserem Special. Windows 7 Download, FAQ und neue Funktionen im Überblick.
Seite 1 von 1

Bluescreen Vor Der Installation (win 7, 64bit)


#1 Mitglied ist offline   Spamcop 

  • Gruppe: aktive Mitglieder
  • Beiträge: 24
  • Beigetreten: 13. Januar 09
  • Reputation: 0
  • Geschlecht:Männlich

geschrieben 13. September 2009 - 12:06

Hallo. :D

Bekomme vor der Installation folgenden Bluescreen:

A problem has been detected and windows has been shut down to prevent damage to your computer.

DRIVER_IRQL_NOT_LESS_OR_EQUAL

If this is the first time you've seen this Stop error screen,
restart your computer. If this screen appears again, follow
these steps:

Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any windows updates you might need.

If problems continue, disable or remove any newly installed hardware or software. Disable
BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove
or disable components, restart your computer, press F8 to select Advanced Startup Options,
and then select Safe Mode.

Technical information:

*** STOP: 0x000000D1 (0x000000000000000A, 0x0000000000000002, 0x0000000000000000,
0xFFFFF88001587FA5)

*** storport.sys - Address FFFFF88001587FA5 base at FFFFF88001585000, DateStamp 4a5bcace


Hab hier nur nen Workaround von MS gefunden "mehr als 3Gb RAM"... also hab ich nen Riegel rausgenommen. Der Bluescreen kommt dann nicht mehr, allerdings friert der Rechner noch vor der Installation ein.

Infos zum System:

ASUS P5N32-E SLI PLUS
Intel Core 2 Quad Q6600
ASUS ENGTX260
4GB OCZ
2x Seagate 250 GB (RAID-0 Verbund)

Noch jmd ne Idee? :D

Gruß Spamcop
0

Anzeige



#2 Mitglied ist offline   jkarl 

  • Gruppe: aktive Mitglieder
  • Beiträge: 34
  • Beigetreten: 17. September 06
  • Reputation: 0

geschrieben 14. September 2009 - 22:17

Du verwendest den Original storport.sys Treiber von MS und nicht irgendeinen Third-Party Treiber? Versuchst Du ein Update oder ein Clean-Install?
0

#3 Mitglied ist offline   Aldjinn 

geschrieben 15. September 2009 - 07:41

Installierst du die 32bit oder 64bit Version? Bei letzterer solltest du mal in deinem BIOS nach einer Einstellungen à la "Memory Remapping" suchen und die ggf. einschalten.
0

#4 Mitglied ist offline   markox 

  • Gruppe: aktive Mitglieder
  • Beiträge: 34
  • Beigetreten: 02. April 05
  • Reputation: 0

geschrieben 16. September 2009 - 14:01

Was ist denn für ein S-ATA Modus eingestellt?
0

Thema verteilen:


Seite 1 von 1

1 Besucher lesen dieses Thema
Mitglieder: 0, Gäste: 1, unsichtbare Mitglieder: 0